/var/run/ndc= not created

[Mark.Andrews at nominum.com]

> 
> Genius!
> 
> out of the 4000 zones there were 2 duplicates and a couple of syntax
> errors (damn that named-bootconf!). Took those out and it worked
> perfectly!
> 
	named-bootconf assumes that named.boot is correct.  If you feed
	it a broken named.boot you will get errors.

	Mark

> Thanks
> 
> N
> 
> > -----Original Message-----
> > From: Mark.Andrews at iengines.com [mailto:Mark.Andrews at iengines.com]
> > Sent: 04 January 2000 12:06
> > To: Nick Bryant
> > Cc: 'bind-users at isc.org'
> > Subject: Re: /var/run/ndc= not created 
> > 
> > 
> > 
> > > 
> > > Ok it isnt made when named is run - which isnt really a 
> > problem as named
> > > works fine... its just everytime i want to do a 
> > named.reboot or .reload
> > > i get the ndc error i mentioned below:
> > > 
> > > > > ndc: error: ctl_client: evConnect(fd 3): Connection refused
> > > > > ndc: error: cannot connect to command channel (/var/run/ndc)
> > > 
> > > which make perfect sence as the command channel isnt there! 
> > Any ideas?
> > > 
> > 	Fix the errors reported when named starts.  Named requires
> > 	/etc/named.conf to be correct or else the command channels are
> > 	not created.
> > 
> > 	Mark
> > 
> > > N
> > > 
> > > > -----Original Message-----
> > > > From: Mark.Andrews at iengines.com [mailto:Mark.Andrews at iengines.com]
> > > > Sent: 30 December 1999 22:51
> > > > To: Nick Bryant
> > > > Cc: 'bind-users at isc.org'
> > > > Subject: Re: /var/run/ndc= not created 
> > > > 
> > > > 
> > > > 
> > > > > 
> > > > > Hi,
> > > > > 
> > > > > Just installed Bind 8.2.2 (patch 5). It didnt create the 
> > > > /var/run/ndc=
> > > > > sockets file during make install as it normally does. 
> > > > 
> > > > 	"make install" does not create this.
> > > > 	It is created when named is run and normally destroyed when
> > > > 	named exits.
> > > > > 
> > > > > So now i get errors like:
> > > > > 
> > > > > ndc: error: ctl_client: evConnect(fd 3): Connection refused
> > > > > ndc: error: cannot connect to command channel (/var/run/ndc)
> > > > > 
> > > > > Anyone know how to create it manually? 
> > > > 
> > > > 	Run named or start it via ndc.
> > > > 
> > > > 	Mark
> > > > > 
> > > > > Thanks
> > > > > 
> > > > > Nick
> > > > > 
> > > > > 
> > > > --
> > > > Mark Andrews, Internet Engines Inc. / Internet Software Consortium
> > > > 1 Seymour St., Dundas Valley, NSW 2117, Australia
> > > > PHONE: +61 2 9871 4742                 INTERNET: 
> > > > Mark.Andrews at iengines.com
> > > > 
> > --
> > Mark Andrews, Nominum Inc. / Internet Software Consortium
> > 1 Seymour St., Dundas Valley, NSW 2117, Australia
> > PHONE: +61 2 9871 4742                 INTERNET: 
> > Mark.Andrews at iengines.com
> > 
> > 
--
Mark Andrews, Nominum Inc. / Internet Software Consortium
1 Seymour St., Dundas Valley, NSW 2117, Australia
PHONE: +61 2 9871 4742                 INTERNET: Mark.Andrews at nominum.com